The HYDRASLEEVE no-purge sampler is used in place of purging and low-flow sampling methods in groundwater monitoring boreholes to obtain representative, real time, discrete interval sample of ALL compounds under natural groundwater flow conditions.

The HydraSleeve is effective for sampling slow recharge wells, for monitoring interfaces, and for concentration profiling. Simply lower the empty sampler to the desired interval, let the well return to undisturbed conditions, and pull the sampler through the sample zone to retrieve a "core" of water at the sample depth.

The HydraSleeve reduces field sampling time significantly. It generates no purge water for disposal and requires no expensive equipment. It can be used to sample slow recharge wells and, because it creates minimal disturbance in the borehole, produces lower turbidity samples compared to bailed or pumped samples.

The HydraSleeve is fast and easy to deploy enabling you to collect samples in less than fifteen minutes! No decontamination or purge water to worry about. No special training or tools required.

The HydraSleeve can be used to sample discrete and multiple intervals in a borehole well casing. Obtain concentration profiles at multiple intervals simultaneously by attaching several HydraSleeve samplers to a single tether line.

Download PDF Datasheet:Hydrasleeve

Hydrasleeve Disposable Samplers

Use the Standard S650 and S1000 Hydrasleeves for sampling from 50mm diameter boreholes. The S650 Hydrasleeve can retrieve a sample volume of 650 ml over a vertical interval of 0.7 to 1.1 metre. The S1000 Hydrasleeves can retrieve a sample volume of 1 litre over a vertical interval of 1 to 2 metres.

Use the Large L1250 Hydrasleeve for sampling from 75mm or 100mm diameter boreholes. The L1250 Hydrasleeve can retrieve a sample volume of 1.25 litre over a vertical interval of 0.7 to 1.1 metre.

For information on the use of the Hydrasleeve, see pdf


Download PDF Datasheet:HydraSleevManual

Code	Description
EHS-110	Hydrasleeve S650 (25mm Dia x 711mm, 650ml)
EHS-111	Hydrasleeve S1000 (25mm Dia x 914mm, 1 litre)
EHS-220	Hydrasleeve L1250 (64mm Diam x 711mm, 1.25 litre)

Reusable Weights for Hydrasleeve

A series of reusable Stainless Steel weights are available for suspending one or more Hydrasleeves in a borehole. The smallest 175g weight is best used with a single Hydrasleeve at up to 60 metres depth; the 275g weights with 2 or 3 Hydrasleeves. Heavier weights (525g) can be used singly or added in line for deploying multiple passive samplers on a single tether line or for working at greater depths.

NEW Stainless Steel Hollow Top Weights can be used to compress the top of the Standard S0 and S1 samplers to within 150mm of the base of the borehole. This allows wells with less than 1to 1.5 metres of water to be sampled.

Code	Description
EWT-150R	SS Weight 175g with eye and split ring (35mm dia)
EWT-227H	SS Hollow Top Weight 227g for Hydrasleeve (41mm OD)
EWT-250R	SS Weight 275g with eye and split ring (35mm dia)
EWT-500R	SS Weight 525g with eye and split ring (35mm dia)
EWT-EYE	SS Eyebolt (DIN580, M6 Thread, 16mm ID eye)
EWT-RING	SS Split Ring (25mm)

Top of Page

The EQUILIBRATOR Passive Diffusion Sampler (PDS or PDB) is used in place of purging and low-flow sampling methods in groundwater monitoring wells to obtain representative, discrete interval samples of Volatile Organic Compounds (VOCs) under natural groundwater flow conditions.

Simply fill the sampler with deionized water, install one or more PDBs in the zone(s) of interest and return at the next sample event to collect samples and replace samplers.

The EQUILIBRATOR is also used in surface water and in stream bed sediments and embankments to identify and monitor VOC contaminant discharge areas.

Download PDF Datasheet:Equilibrator

Equilibrator Disposable Diffusion Sampler

Code	Description
EEQ-350	Equilibrator Diffusion Sampler (350 ml)

Reusable Hangers and Accessories for Equilibrator

For suspending 1 or 2 diffusion samplers in a borehole, the optional stainless steel hanger provides the simplest solution. By adding a standard weight this method is typically used up to a depth of approximately 25 metres below water level. See pdf for instructions.

The easiest way to string 3 or more samplers together is to hang a series of diffusion samplers from a single cord tether with a heavier weight. This method with the 567kg weight is typicallyused for depths in excess of 25 metres. For depths below water in excess of 75 metres additional in-line 567 g weights are recommended. See pdf for instructions.


Download PDF Datasheet:EQInstructions

Code	Description
EEH-310	Stainless Steel Hangers for Equilibrator (Reusable)
ESC-135	Plastic Snap Connectors for holding Equilibrator to Tether Line
CT25	Pack of 25 Cable Ties (200mm)
EFK-306	Fill Kit (Reusable) for Equilibrator

Reusable Weights for Equilibrator

A series of reusable Stainless Steel weights are available for suspending one or more Equilibrators in a borehole. The smallest 175g weight is best used with a single Equilibrator at up to 60 metres depth; the 275g weights with 1 or 2 Equilibrators. Heavier weights (525g) can be used singly or added in line for deploying multiple passive samplers on a single tether line or for working at greater depths.

Code	Description
EWT-150R	SS Weight 175g with eye and split ring (35mm dia)
EWT-250R	SS Weight 275g with eye and split ring (35mm dia)
EWT-500R	SS Weight 525g with eye and split ring (35mm dia)
EWT-EYE	SS Eyebolt (DIN580, M6 Thread, 16mm ID eye)
EWT-RING	SS Split Ring (25mm)

Top of Page

Tag Line

The Solinst 103 "Tag Line" is a 1.6mm diameter stranded stainless steel cable marked at one metre intervals with low profile bonded markings. The end of the cable is equiped with a clip which can be attached to a variety of devices for temporarily suspending in boreholes including HydraSleeve and Equilibrator Passive Samplers. The supplied tape guide helps protect the cable from damage caused by rubbing against the edge of borehole casing during use.

Using a tag line is quick and easy and because the tape is already marked at 1 metre intervals, cuts out the need to measure the length of cord before it is used.

Each Tag Line is supplied with a 0.7kg weight for use as a plumb line. The weight has tapered ends to minimise snagging in the borehole and can be clipped on and off the cable. The cable itself has a minimal breaking strength of 122 kg.


Download PDF Datasheet:Tag Line

Code	Description
S103/030	30m Tag Line with 0.7kg weight
S103/060	60m Tag Line with 0.7kg weight
S103/100	100m Tag Line with 0.7kg weight
S103/200	200m Tag Line with 0.7kg weight
S103/300	300m Tag Line with 0.7kg weight

Cord and SS Cable
An inexpensive and disposable option for bailing.

Code	Description
BC/K35-50	Lifting Cord - 3.5mm diam polyester cord (50m)
BC/K35-300	Lifting Cord - 3.5mm diam polyester cord (300m)
S3001/SC1002	100m x 2.0mm Stainless Steel Support Cable (spooled)
S3001/RG1002	Stainless Steel Rope Grip (For SC1002 cable) (Flat)

Hand Reel with Removable Spool

Make life easier and tidier with this handy reel for winding up cord or tethers. The spool is removable, and additional spools can be purchased. Each spool has an approximate capacity of 100m of 3.5mm cord.

Code	Description
ERL-110	Hand Reel with removable spool (holds 100m of 3.5mm cord)
ERL-111	Extra Spool for Hand Reel

Well Caps

EnviroCap locking well caps are attached to the top of well casing and serve the dual functions of preventing surface water from entering the well through the top of the casing and restricting access by unauthorized persons.

EnviroCaps feature an exclusive built in locking system that is completely sealed from the outside environment to eliminate replacement cost of failed locks due to rust, corrosion, and debris. Unlike conventional caps, EnviroCap does not come loose in the casing.

The EnviroCap cannot be opened without using the special magnetic EnviroCap Key (universal) which prevents unauthorised access to the borehole


Download PDF Datasheet:Envirocap

Code	Description
S3001/SWH2	Locking Well Cap - 48mm (2 inch)
S3001/SWH4	Locking Well Cap - 96mm (4 inch)
S3001/WHKey	Locking Well Cap Key

Disposable Gloves (Green Nitrile)

"Touch N Tuff" powder free green nitrile disposable gloves contain no natural latex proteins thereby eliminating Type I allergies associated with latex gloves. They offer superior abrasion and puncture resistance when compared to either Latex or Vinyl gloves. Excellent resistance to oil's, fats, grease and other chemicals. Provides protection against dirt, contamination and irritants. Medical Grade Product. Box contains 100 gloves.

Code	Description
GL-MEDIUM	Gloves - "Touch N Tuff" powder free green nitrile - Medium - 100 per box
GL-LARGE	Gloves - "Touch N Tuff" powder free green nitrile - Large - 100 per box

Top of Page

The Solinst Discrete Interval Sampler is a high quality stainless steel sampler with Teflon ball valves and Viton o-rings. It is connected to a narrow diameter air tube on a reel. The sampler is pressurised before lowering into the borehole. This prevents any flow of water into the sampler during lowering through the water column. Once the sample depth is reached, the pressure is released, and the sampler fills. Once full, the sampler can be repressurised to maintain in-situ pressure and then brought to surface.

The sampler is ideal for groundwater sampling below an oil/product layer, for retrieving heavy oil (DNAPL) samples or for volatile and dissolved gas sampling of groundwater in boreholes.

Download PDF Datasheet:DIS

Discrete Interval Sampler Kits [25.4mm (1 inch) x 610mm (2ft)]
25.4mm diameter x 610mm long Samplers have a capacity of approximately 200 ml of water.

Code	Description
S425/102/30	30m DIS Kit: 25.4mm (1") x 610mm (2ft) SS Sampler, with reel, tubing, pump and SRD
S425/102/60	60m DIS Kit: 25.4mm (1") x 610mm (2ft) SS Sampler, with reel, tubing, pump and SRD
S425/102/150	150m DIS Kit: 25.4mm (1") x 610mm (2ft) SS Sampler with reel, tubing, pump and SRD

Discrete Interval Sampler Kits [42mm (1.66") x 610mm (2ft)]
42mm diameter x 610mm long Samplers have a capacity of approximately 580 ml of water.

Code	Description
S425/162/30	30m DIS kit: 42mm (1.66") x 610mm (2ft) SS Sampler, with reel, tubing, pump and SRD
S425/162/60	60m DIS Kit: 42mm (1.66") x 610mm (2ft) SS Sampler, with reel, tubing, pump and SRD
S425/162/150	150m DIS Kit: 42mm (1.66") x 610mm (2ft) SS Sampler, with reel, tubing, pump and SRD

Discrete Interval Sampler Bodies

Code	Description
S425/102	25.4mm (1") dia x 610mm (2ft) SS Sampler inc SRD
S425/104	25.4mm (1") dia x 1220mm (4ft) SS Sampler inc SRD (OBSOLETE)
S425/202	51mm (2") dia x 610mm (2ft) Stainless Steel Sampler inc SRD
S425/162	42mm (1.66") dia 610mm (2ft) SS Sampler inc valve and SRD
S425/162/TV	42mm (1.66") dia x 610mm (2ft) SS Sampler/Transportable Vessel inc valve and SRD

Discrete Interval Sampler Accessories

Code	Description
S425/HPHP	High Pressure Hand Pump
S425/SRD12	Sample Release Device (spare) - 25.4mm (1") and 51mm (2")
S425/SRD16	Sample Release Device (spare) - 42mm (1.66")
S-LD14N	1/4 x 0.17 inch (~6 x 4 mm) LDPE Tubing
SC1000	SC1000 Tubing Reel with vent switch (100m limit)
SC2000	SC2000 Tubing Reel with vent switch (150m limit)

Top of Page